Ⅰ. Safety Precautions for Use of Figaro Gas Sensors
- Carefully read product information and other technical information provided by Figaro before using our products, and confirm specifications and operating conditions.
- When designing an application circuit, please make sure that an accidental short circuit or open circuit of other electronic components would not cause the sensor to be subjected to excessive voltage, current, or temperatures exceeding the rated values.
- When designing application products, please make sure that a gas sensor malfunction would not
1) cause adverse effects on other components,
2) directly or indirectly impair the safety of application products that use gas sensors (e.g., emit smoke, cause fire, or other unstable states of application products). - Consider adding safety measures for fail-safe where necessary, such as a protection circuit.
Ⅱ. Cautions for Use of Electrochemical-type (TGS5000 Series) Gas Sensors
【Conditions for use and storage】
-
1) Rated temperature and humidity conditionsUsing or storing the sensor in an environment outside the rated temperature and humidity range may cause physical damage and/or affect the sensor characteristics.
-
2) Storage conditionsIf a sensor with water reservoir is stored in an airtight container such as a sealed bag, dew condensation may occur inside the sensor due to ambient temperature change, eventually affecting sensor sensitivity. Keep this type of the sensor in clean air and not in a completely sealed container.
When the sensor without reservoir is stored in a polluted environment for a long time, store the sensor in a sealed bag whose material does not emit odor or gas. Do not use dehumidifiers such as silica gel in the bag. -
3) CondensationIf water condenses inside the sensor housing, sensor characteristics may drift.
-
4) FreezingWhen a sensor with the reservoir is subjected to temperatures below 0˚C, the water in the reservoir may freeze. Expansion of water volume due to freezing may cause some deformation of the sensor, and eventually change in its characteristics. This risk can be mitigated if the sensor is positioned with the cap (working electrode) facing up.
-
5) Oxygen concentrationThe sensor cannot properly operate in a zero oxygen content atmosphere.
-
6) High concentration of gasesSensor performance may be affected if exposed to a high concentration of gases for a long period of time during the operating or storage period.
-
7) Organic vaporsIf the sensor is exposed to organic vapors generated from alcohol, acetone, volatile oil etc., organic vapors will adsorb onto the sensing element surface, and sensor performance may be affected.
-
8) Dusts and oil mistSensor performance may be affected if exposed where excessive dust, fine particles, or oil mist is present.
-
9) Alkaline metalsSensor characteristics may be changed if the sensor is contaminated by alkaline metals. Avoid contamination by alkaline metals, especially salt water spray.
-
10) High concentration of corrosive gasesSensor performance may be affected if exposed to a high concentration of sulfur-based or chlorine-based corrosive gases for extended periods. Avoid usage and storage in highly corrosive environments.
-
11) Sensor with filterSensor performance may be affected if the sensor with filter is exposed to organic vapors such as alcohol for extended periods, causing breakthrough of the filter. Avoid usage and storage in such environments.
【 Handling 】
-
1) Applied voltageIf voltage of +10mV or higher, or -10mV or lower is applied to the sensor, physical damage to the sensor may occuror sensor characteristics may be affected. Do not use the sensor once such excessive voltage is applied.
-
2) Mechanical shock and vibrationAvoid mechanical shock. Deformation of the sensor, or change in sensor characteristics may occur if the sensor is subjected to a strong shock or vibration. Do not use the sensor if subjected to a drop or other mechanical shock.
-
3) No soakingAvoid contact with water. Sensor characteristics may be affected due to soaking or splashing the sensor with water.
-
4) No disassembly or deformationUnder no circumstances should the sensor be disassembled, nor should the sensor structure be deformed. Such action would void the sensor warranty.
-
5) Gas inletDo not block the gas inlet of sensor. The sensor would not work properly with a clogged inlet.
【 Mounting process 】
-
1) SolderingManual soldering is recommended. High concentrations of flux or excessive soldering heat may affect sensor characteristics. When wave soldering is used, rosin flux with minimal chlorine should be used, and a trial assembly test should be conducted before production starts to see if there would be any influence to sensor characteristics.
-
2) Resin coatingWhen a resin coating is applied on a printed circuit board for improving its resistance to moisture, the chemical solvent contained in the coating material may affect sensor characteristics. Sample testing should be conducted to see if this process would adversely affect sensor characteristics.
-
3) Electro static dischargeExercise necessary precaution against ESD during mounting of the sensors on finished instruments.
-
4) ResonanceExcessive vibration may cause damage of the sensor structure or breakage of the sensor components at the resonance frequency. Usage of compressed air drivers or ultrasonic welders on assembly lines may cause such vibration to the sensor. Before using such equipment, preliminary tests should be conducted to verify that there will be no influence on sensor characteristics.
【 Application design 】
-
1) Preheating timeAs unpowered storage becomes longer, a longer stabilization time is required due to polarization occurring during the storage period. When designing a detector circuit, an anti-polarization circuit is recommended.
-
2) FreezingWhen a sensor with a reservoir is subjected to temperatures below 0˚C, it is possible that the water in the reservoir may freeze. Since water volume will expand when freezing, the sensor can may undergo some deformation. Care should be taken in the design of the detector to ensure that the sensor is not placed too close to other components or the circuit pattern on a PCB, so that such deformation would not cause the sensor to come in contact with these items.
-
3) Position dependencyIt is recommended that sensors with a reservoir be placed in a vertical position with the cap (working electrode) upward when the detector is in use, as the sensor can may undergo some deformation and sensor characteristics may be affected due to expanded water volume when freezing.
-
4) Foreign conductive objectsIf foreign conductive objects get into the sensor, short-circuit may occur inside the sensor. When such conditions are expected to be encountered, installation of an external air filter is recommended.
-
5) Fitness for purposeBefore usage of the sensor, customers should verify and ensure that the sensor will work properly under the conditions where they intend to use it and that the sensor is fit for the purpose for which customers wish to use it.